Thermoplastic LPG Filling Pipe XD-5 -with 2x 1/2" UNF Straight Couplings

Thermoplastic LPG Filling Pipe XD-5 -with 2x 1/2" UNF Straight Couplings

Self assemble and cut to length LPG filling hose with 2x Straight connections 1/2" UNF (19mm)

CHOOSE THE LENGTH OF THE SUPPLIED THERMOPLASTIC PIPE

This type of LPG filling line has many advantages over standard filling hose. This way you can assemble it yourself according to your needs and you can shorten it to the right length yourself and then connect the couplings. This makes this type of product very flexible in its applicability.

Can be used instead of copper LPG pipe with outer diameter Ø8mm. Has an even larger internal diameter than 8mm copper and in terms of flow capacity equal to 10mm copper pipe.

Brand: LPG FIT
UPC Number: LPG-XD-5 H05
Manufacturer code: LPG-XD-5
Approval number: E4 67R-010247
Inner diameter: Ø8mm
Outer diameter: Ø12,3mm
Pressure class: 67R-01 Class 1 (max. 30 bar)

This type of filling hose consists of the following parts:

- 2x Straight Connection 1/2 "UNF (19mm) for tank / filling connection

- Desired length thermoplastic pipe type XD-5. It can then be shortened to the desired length.

 
Instructions:

Make the Thermoplastic LPG pipe to the desired length and neatly shorten the ends without kinking the pipe. (Piping must remain nicely round).

Slide the OETIKER hose clamp over the LPG pipe.

Apply a little creeping oil to the O-rings of the couplings before sliding the LPG pipe over the coupler.

Seal the connection well by properly clamping the OETIKER hose clamp.

 
Application: Filling various types of LPG tanks (4-hole LPG tank / MultiValve tank (Ø8mm) / Vapor tanks / gas bottles).

 
The filling line makes a connection from the outer filling connection to the LPG tank. Choose the required length and connectors for your application.

TIP!
Do you prefer to use a filling hose with fixed couplings? Then look here.
For various filling connections, look here.
If you also want to be able to fill in other countries, look here.

 
NB!
A plastic LPG pipe is not connected directly to an LPG part, but coupling pieces are used on the ends of the pipe. These come in different shapes and sizes. There are also several types of plastic LPG pipe available. There are different diameters, but also brands and types of connectors. Make sure you use the correct one for your application in combination with the correct coupling pieces on the ends of the plastic pipe.

 
The plastic pipe can be shortened to the desired length. Use a good sharp hose cutter or else a cutter for this. Cut the pipe neatly straight.

 
NB!
Check the type of connection on the parts to which you want to connect the LPG pipe, such as the tank, gas valves, etc.

 
This type of pipe uses Ø8 mm compression connections and therefore only fits on parts with such a type of connection.

 
NB!
General safety advice for LPG Pipe:

- The LPG pipe may not be placed close to heat sources (for example an exhaust pipe). Maintain a minimum distance of 10 cm. Or use a heat shield.
- The LPG pipe may not be placed lower than the lowest point of the vehicle. In other words: At a distance of 15 cm from the pipe, there must always be a fixed part of the vehicle lower down. This rule prevents the pipe from touching the road surface.
- LPG pipe must be attached to non-moving (fixed) parts of the vehicle by means of pipe brackets. The maximum mutual distance between the pipe brackets must not exceed 40 cm.
- Consult the RDW rules for the exact and other guidelines.

ONLY USE CORRESPONDING TERMINAL COUPLINGS OF LPG-FIT TYPE XD-5

The corresponding Terminal couplings fit most 8mm compression connections of evaporators, gas valves, multivalves, quick-closing valves, etc.

But there are also associated terminal couplings that fit on an electric tank extraction valve or filling connections.

 
Outer diameter pipe connector: Ø8mm

Outer diameter of plastic gas pipe: ≈ Ø12.3mm

Inner diameter plastic gas pipe: ≈ Ø8mm

 
Instead of copper pipe, plastic pipe is nowadays used with various advantages such as flexibility and that it does not kink quickly. To be able to connect the plastic pipe to another part, just as you would with a copper pipe, it is necessary to connect an end piece (coupling piece) of that type of pipe, which in turn is fitted with a Ø8 mm pipe (just like a copper pipe).

 
Suitable for: LPG 4-Hole Tanks (Vapor Tanks) and LPG Tanks with Multivale 8mm connection (outlet) and gas ash whistles and evaporators etc with 8mm compression connection.